Dri Sleeper Eclipse Bed Wetting Alarm
The Dri Sleeper bedwetting alarm has sound technology to assist the person using it to become dry at night. The Dri Sleeper Eclipse is a simple wireless device. No wires or plugs to get tangle or become unplugged, no uncomfortable clip on the shoulder.
The Eclipse is very simple to use and has two parts. A solid Urosensor which is safely secreted into the pants or diaper which when it becomes wet, a nearby alarm unit sounds to wake the the person. By using this device, the brain eventually learns to react and wake up when the sensation is felt to urinate.
The Urosensor is solid state and water sensitive, it has no moving parts and is unlikely to wear out. It is orange in colour with black sensor bars and appealing to young eyes. It has a sealed ‘tamper proof’ battery within.
The Alarm unit is two tone blue, and this unit sits nearby to the user on bedside table or other bedroom furniture – it has a volume control (which is set to high by the manufacturer). A second alarm unit can be purchased (if considered necessary) for use in the carer’s room. The Urosensor can be stowed neatly on top of the alarm unit to keep neat and tidy.
There a many causes for bedwetting which we will not discuss here, however with the use of the Dri Sleeper bedwetting alarms there is a 90% success rate in curing the problem.
Treatment would normally take around 6 weeks, though some take a shorter time, whilst others take considerably longer.
The problem of bedwetting can be a huge embarrassment for children, causing all kinds of problems at home and school, whilst dealing with continual wet bedding for parents can be frustrating tiring and annoying.
The treatment by using this device needs to be discussed with your child so there is a joint effort to try and stop the problem.
Children 5 years and older should be considered for these devices.
We can offer support and advice regarding the use of the product.
You are able to order the following
- Single complete Eclipse Alarm
- Extra Alarm Unit
- Spare Urosensor
How long will treatment take?
Typically treatment is 6 to 8 weeks, but with treatment of any condition, there is a great deal of variability. If you are familiar with the normal distribution graph, this describes the treatment time parameter, eg. some children will respond and be finished with treatment within a week, a larger group take 3–8 weeks, and a small group takes longer. While it is quite normal for some children to take longer, if you become concerned about the time.
- Don’t limit drinks – it will not help, and in fact it may make things worse. This is because the bedwetter produces high amounts of urine because a hormone which is produced at night in adults and most children to cut down the production of urine when asleep, is not produced in large enough amounts in bedwetters. For this reason their production of urine is too high. So the brain of the bedwetter tells the kidneys to produce just as much urine at night as it does during the day, and limiting drinks will not change the brain’s message to the kidneys.
- Don’t expect that setting an alarm clock or waking your child at a regular time to empty the bladder will teach the child to wake – it doesn’t.
- Don’t blame your child or use punishment, as you can see it is not the child’s fault. An anxious child will be less able to cooperate with you in the treatment.
Pharmacological Treatment of Bed Wetting Synthetic hormones, and antidepressants may be prescribed for bed wetting.
Treatment with synthetic hormones reduces the amount of urine produced during the night, whereas antidepressants make the bladder muscles relax whilst causing the smooth muscle of the bladder neck to contract inhibiting involuntary urination.
These can be effective for short term treatment, e.g when the child has to go on school camp, or for treatment of distressed older children, if other treatments have been unsuccessful.
For you to be a team, there has to be an alignment between you and your child. Maybe right now you are trying to use logic to get your child to agree to doing something about the problem of bedwetting, but perhaps your child is in an emotional, negative mode and so there is no alignment between the logic that you are trying to use, and the emotional, maybe negative state your child is in.
So when I say that you both need to be aligned, this means that you both need to be in a logical, fact based mode in which there is little or no emotion.
The way to get to the position of both being aligned is to have a very logical, unemotional conversation with your child about his or her bedwetting. In particular ask whether it bothers him or her, and whether he or she would like to stop wetting the bed. If the answer is yes, then explain that you have to work on it together as a team, and the team is you, your child and the DRI Sleeper®. Explain that you all want the same thing, and that is for him or her to be able to wake up if he or she needs to go to the bathroom in the night.
Explain that the issue with bedwetting is that he or she is too much asleep to wake up, and the only way to stop wetting the bed is to learn to wake up, but that you both know that he or she cannot do that alone (it’s important that you also have agreement on that).
So what you are asking your child for, is for him or her to agree to work as a team with you, and the DRI Sleeper®.
The next step is to summarize what you have both agreed on and to make sure that your child understands that you are going to work together as a team to beat the bedwetting.
The conversation you have just had with your child is an example of how good communication proceeds, and so it is important that you tell your child how grown up he or she has been in listening and understanding how you are going to beat the bedwetting as a team.
It may be necessary to have this conversation again if there are objections, but at all times stay unemotional and just stick to the facts as I have explained above.
Finally if your child says that he or she does not want to work as a team and will not use the DRI Sleeper®, then tell him or her that you will leave it until he or she is old enough and ready to work as a team. However, because he or she has decided to keep wetting the bed then he or she will have to look after it, i.e, to change the bed linen and put everything in the wash every day, and to make the bed up again (depending on the age of your child you may need to help). If it happens in the night he or she will have to do it then as well.
The point of this is that even a child must learn that decisions have consequences. Cooperation has the consequence of working as a team and being helped to solve things, not cooperating means the problem continues and you have to look after it yourself. That’s a very important lesson of life.
Over the next few weeks the child is learning to react more and more quickly to the alarm, and then begins to “beat the buzzer” by waking up before starting to pass urine. Now the child is beginning to respond to the sensation of the bladder filling, which is exactly where the treatment has been heading to.
The process is then to keep using the DRI Sleeper® every night until there have been 14 nights in a row with no triggering of the alarm, and no bedwetting.
All children who wet the bed sleep very deeply, but research indicates that all young children sleep more heavily than adults, because they spend more time in the deep sleep phases. Therefore there is no consistent evidence that children who wet the bed actually sleep more heavily than children who do not. Nonetheless parents will usually agree that their bedwetter sleeps more heavily that their other children. So we have designed the DRI Sleeper® alarm to be maximally alerting for heavy sleepers, firstly because of its loudness and position on the shoulder, and secondly because the frequency is particularly alerting.
There are several reasons why the DRI Sleeper® is more likely to wake your child.
- The alarm unit of the DRI Sleeper™ is placed on a Velcro patch on the shoulder of the child, and so is much closer than an alarm clock, and therefore, while the alarm clock may appear to be quite loud, it is not as loud as the DRI Sleeper®.
- The DRI Sleeper® is triggered as the child starts to pass urine, and this is likely to be when the stage of sleep is closer to waking, and so there is a higher chance of the child waking to the sound.
- An alarm clock being set to go off at a particular time will have no relationship to the child experiencing the urge to urinate, and so not only is the alarm clock not as loud as the DRI Sleeper®, but it is going off without there being the important relationship between the sound and the urge to empty the bladder, and the child being in a lighter state of sleep.
With these children the strategy is that you hear the alarm, go into the room, put on the light, say your child’s name, and if no waking is happening, wipe your child’s face with a cool damp cloth. Leave the alarm beeping.
Then have your child get up (by themselves) and go to the bathroom with the alarm still sounding, and ONLY then should you unplug the alarm.
The reason for this is so that waking is happening with the alarm sounding, and a link between waking and the sound of the alarm can be formed in your child’s brain.
It is very important that in the morning that your child remembers the alarm sounding and going to the bathroom, because only if your child remembers will learning happen effectively.
However, for these children there is this extra step in the treatment program and so expect it to take longer.
Another strategy to assist with waking is what I call a “priming” strategy. It is possible to “prime” your brain to remember to do something in the future, for example we can say to ourselves that we need to remember an appointment next Tuesday, and in fact as Tuesday approaches the thought about that meeting comes into our mind. People also use the same strategy when they need to wake early in the morning, they set the alarm clock for the early hour, but almost invariably will wake up before the alarm clock. What I suggest is that as your child is preparing for bed, that you have her or him lie down in bed just as he or she would when he or she is sleeping, have the alarm attached to the shoulder, and you trigger the alarm with a coin or something similar. Your child is to get up, after a few moments unplug the alarm, and go to the bathroom, pretending to use the bathroom as she or he would if he or she needed to pass urine. Practise doing this five times in order to assist (priming) your child’s brain to be more ready to respond to the alarm when it sounds during the night.
When there is still no progress (and I guess it’s no comfort to you that not many children are in this category), a part of the learning to wake to the alarm is practised during the day.
Have the alarm box already attached to a favourite pyjama top, or maybe a T shirt that you have bought especially for this treatment (anything that makes the process special will help).
Check the DRI Sleeper®. alarm is working correctly by plugging in the Urosensor™ and touching the Urosensor™ surface with a coin such as a dime to and noting that it beeps.
Before you follow this routine, make sure you know it well. Explain it to your child, and make sure your child understands that this practise is teaching the brain to be ready to wake to the buzzer, and, that with practise your child’s brain will get fast enough to beat the buzzer. Then he or she will have dry beds.
- From dinner time on, have your child drink extra liquids. This may sound strange, but we are wanting to get plenty of practise at the routine of responding to the alarm.
- Have your child tell you when he or she needs to go to the bathroom (you could call it having a “bladder signal” or any other term you like, as long as it is one that you have agreed on and you continue to use that term).
- Immediately go with your child to the bedroom, have him or her put on the pyjama top with the alarm box attached, lie on the bed, and pretend to be sleeping. Plug in the Urosensor™ of the DRI Sleeper® Excel (or switch on the DRI Sleeper® Eclipse) and you pick up the Urosensor™ and hold it.
- When he or she is relaxed, you make the alarm “beep” by touching the Urosensor™ sensing surface with a dime. Then your child is to get up and you both run right along to the bathroom, with the alarm still beeping.
- Have him or her unplug the Urosensor™ from the DRI Sleeper® Excel alarm box (or switch off the DRI Sleeper® Eclipse), just as would happen if this were during the night.
- When possible, another parent or sibling may also help, by going to the parents’ room and when the DRI Sleeper® alarm starts beeping, “race” the child into the bathroom. Children of this age tend to like this kind of competitive involvement. It also encourages the sense of urgency to react to the DRI Sleeper® alarm beeping.
- Have your child splash his or her face vigorously five times in a row with cold water. Then pretend to use the toilet for a few seconds as if to urinate, and have your child say, “I have a bladder signal (or whatever is the term you have agreed on), but I can wait to urinate.”
Return to the bedroom and repeat steps 3 to 7 above four more times. If your child cannot hold off urinating, then let him or her urinate and then continue until you have practised steps 3 to 7 five times in total.
If after a week your child is still not waking to the DRI Sleeper® alarm at night, then increase the number of repetitions to 10 times per evening. For more difficult cases go to 20 repetitions in the 3rd week.
If even this is not successful (and that’s very rare) then leave it for a few months to allow more brain maturing and then start again.
My child wets several times a night, and so does that mean my child will always have to get up to go to the bathroom during the night?
The answer is no, and here is another aspect of bedwetting that is not understood. As I mentioned before, children who suffer primary bedwetting (never having been dry at night since coming out of diapers) produce too much urine during the night, as well as being unable to wake themselves. However, a consistent observation from my experience over 30 years, is that after being successfully treated with the DRI Sleeper®, within a month or two (and often more quickly) the child begins to sleep right through the night, and does not wet the bed, but also does not need to get up to go to the bathroom. This suggests that they are now moving into the more adult pattern of producing less urine while they are asleep and therefore most often not needing to get up during the night. However, this is a guess, and has not been researched at this stage.’
A few children may go back to bedwetting after a few months, and in that case simply using the DRI Sleeper®. again will fix the problem. However there is also a method called over-learning which can be used to prevent relapsing and to strengthen the training.
When your child has had 14 consecutive dry nights with no wetting and so no alarm activation, start to have him or her drink an 8-10 oz glass of water around a half an hour before bed. What this will do is make it necessary for him or her to need to go to the bathroom two or three hours later, and either it will cause the alarm to be triggered, or he or she will wake up. Either way this brings about more learning to respond to the sensations of the bladder filling. Continue with this for 7 nights. Then stop the extra drinks (let your child drink what he or she wants to) but keep the DRI Sleeper® attached each night until he or she has achieved 14 dry nights.
Yes, parents have used the DRI Sleeper® successfully during the day to teach the child to tune into their bladder signals. Even from using the DRI Sleeper® at night many parents notice an improvement during the day because their child has become more aware of daytime bladder signals.
My child has special needs, can the DRI Sleeper® be used to help with toilet training?
Yes, the DRI Sleeper® has been used successfully for children with special needs to assist them to become toilet trained so that they can become mainstreamed at school.
Both the DRI Sleeper® Eclipse and DRI Sleeper® Excel have a volume control, but it is inside so that a child is not likely to see it readily and turn the volume down when you have left his or her bedroom.
Both are tuned to high volume (around 98 dBA at the ear) and rarely do parents want to turn them down.
The DRI Sleeper® Eclipse (wireless) because it can be put further away can be tuned to even higher volume (approximately 106 dBA), but it will switch off after 2 minutes and so there is no risk to hearing.
The Urosensor™ is put inside a mini pad or pantyliner (any inexpensive mini pad or pantyliner will do), and this is done by cutting a 1 inch slit in the absorbing layers towards the top or bottom edge of the mini pad or pantyliner. Put the point of the scissors inside the slit, and moving them backwards and forwards and downwards, create a tunnel inside the absorbing layers so that you can slip the detector inside. Although the Urosensor™ will usually stay inside the tunnel by itself, to ensure that it does not pull out, you can tape across the slit with a sticky tape. With the slit facing upwards, the mini pad or pantyliner is stuck into the crutch of the underwear using the sticky back surface of the pantyliner or mini pad.
Consistently we have found that putting the Urosensor™ in a mini pad is the most effective, because the mini pad provides a collecting area that is even wider than the Urosensor™, and it is very absorbing, and so quickly catches the urine and directs it onto the Urosensor™. You will also find that once your child is starting to respond to the DRI Sleeper® that only a patch on the minipad will get wet, not the underwear.
If you prefer not to use the mini pad or pantyliner, then the Urosensor™ can be put in between two pairs of underpants, or you can cut some rectangles of any cotton material and sew a rectangle into the crutch of the underwear, making sure that it is just wide enough for the detector to slip inside and to be reasonably tight. The opening will face upwards.
Over more than 25 years of treating bedwetting and developing bedwetting alarms, we have found that having a small detector, such as a clip or domes, attaching to underwear may appear to be an effective and simple way of attaching the detector, but in our experience it is too easy for boys in particular to miss the small clip or dome and so the alarm is not triggered. Clips and domes are also likely to come unclipped. For this reason, we developed Urosensors™ which are long enough and wide enough for the first amount of urine to trigger the alarm.
The Urosensor™ is suitable to use in a pull-up. Simply cut a 1 inch (25 millimetres) slit in the pull-up in the crutch area, insert the point of the scissors into the slit, and moving the scissors from side to side, make a small tunnel into which you can insert the detector. To make sure that the Urosensor™ stays in place, it can be useful to tape across the slit once you have put the detector inside.
The pull-up has granules which are designed to absorb liquid and may keep the Urosensor™ too dry and fail to trigger. In this case either ensure the Urosensor™ is as close to the surface of the pull-up as possible, or put in a minipad and stick that in the crutch of the pull-up.
The Urosensors™ are moulded units and so no urine or water can get inside. Therefore, it is simple to wash with soap and water, or if you want an even higher standard of hygiene, then you can clean it in alcohol (e.g., rubbing alcohol from any pharmacy).
1. DRI Sleeper® Excel (with plug-in Urosensor™). Think of the Urosensor™ as you would an earphone on a personal radio or an iPod. With reasonable care, the radio or iPod lasts for many years and so does the DRI Sleeper® alarm unit. However, the earphone is the consumable item of the iPod and personal radio and needs replacing from time to time. Just as people often have a spare earphone on hand, our advice is that a spare Urosensor™ is a good idea. Because the Urosensor™ is used by a child, the exact life of the Urosensor™ is hard to predict.
2. DRI Sleeper® Eclipse (wireless). The wireless Urosensor™ should not need replacing because it has no moving parts. The internal battery should give up to three years life, especially of it is “docked” on the DRI Sleeper® alarm unit when not in use.
The wire is 2.5 feet long (850 millimetres) and is suitable for children aged five years, through to young teenagers. For older children and adults the DRI Sleeper® Eclipse wireless model is more suitable because there is no wire connection.
How is the DRI Sleeper® alarm different from many other bedwetting the alarms?
The DRI Sleeper® alarms have special electronics. When the Urosensor™ is wet by urine, it triggers the alarm to start beeping, but then the Urosensor™ no longer has current running through it.
This is quite different from many other alarms, because with those alarms, all the time that the alarm is sounding, they have current flowing through the Urosensor™ and while this cannot cause a shock, it can cause the urine to become acidic and irritate sensitive skin.
In the case of the DRI Sleeper®, this cannot happen, because there is no current continuing to run in the Urosensor™.
The DRI Sleeper® Excel runs on six volts and the DRI Sleeper®, Eclipse on three volts. Both use only a tiny current, and are so safe that you can put the Urosensor™ on your tongue, and trigger the alarm, but you will feel nothing. For much less than a second a few microamps (which you can not feel) pass through the Urosensor™ and trigger the DRI Sleeper® alarm.
The DRI Sleeper® Eclipse has an on-off switch.
DRI Sleeper® Excel. The Urosensor™ plugs into the alarm unit and this switches it on so that it is ready to detect urine. When the alarm has been triggered by the urine, the alarm will keep on beeping until the Urosensor™ is unplugged from the DRI Sleeper® Excel alarm unit. This switches the alarm off, and also resets it ready to be switched on again when the Urosensor™ is plugged in.
DRI Sleeper® Excel
The batteries are 4 X 1.5 volt alkaline “button type” similar to those used in a calculator. (Panasonic LR 44 or equivalent, we put a sticker inside the battery compartment showing the equivalent ones which are suitable). the batteries should last at least a year providing the sensor is removed when not in use.
DRI Sleeper® Eclipse
The DRI Sleeper® alarm unit has a Panasonic 2354 and this battery must be used in replacement. Battery life will depend on usage. The battery in the alarm base should last 3 months with nightly use if the alarm is triggered twice a night, provided the alarm is turned off when not in use. The battery in the Urosensor should last 12 months with nightly use if it triggers the alarm twice a night.